S04 Reverberation Time (WELL v2, Q2 2025)
Concept: Sound · Type: Optimization · Maximum points: 2
Intent
Design spaces in accordance with comfortable reverberation times that support speech intelligibility, vocal effort and are conducive to concentration.Summary
This WELL feature requires that steps be taken to address acoustical comfort, by controlling reverberation time based on room functionality.Issue
Reverberation time is the length of time taken for a sound to decay by 60 dB from an initial impulse level. The length of reverberation time is a function of room size, surface area and sound absorbing properties of surface finishes. Spaces with longer reverberation times may be larger in volume with hard surfaces that reflect sound. Spaces with shorter reverberation may be smaller with softer surfaces that absorb sound. Spaces with high reverberation may have increased ambient noise levels and reduce speech intelligibility (e.g., public address, speech reinforcement and unamplified speech). Studies have shown that high reverberation times in classrooms increase auditory workload in students and reduce cognition, memory retention and concentration.1–4 Similarly, studies have shown that high reverberation reduces speech intelligibility among hard of hearing and non-native speaking populations.5–8Evidence
Reverberation time can be controlled by adding absorptive surface finishes at ceilings, walls and furniture.9–11 Projects that can alter room geometry can change layouts and room dimensions to support optimal reverberation times, as needed. Reducing reflective surfaces, such as glass, drywall, stone or similar, will also reduce reflected sound energy, which increases reverberation time. Reducing reverberation time also allows audio equipment for telecommunication/AV, speech reinforcement or public address to operate with higher speech intelligibility performance.5,12–14Requirements
S04.1 Achieve Reverberation Time Thresholds — 2 points
Applies to: All Spaces; excluding Dwelling Units, Guest Rooms.
Meet any one of the following options:
Option 1: Reverberation time, design
For projects in which the room types listed in the table cumulatively make up at least 10% of occupiable project area, the following requirements are met:
Reverberation time is within the ranges shown in the following table:
Room Type
Room Volume, v (cubic {{well-unit}}feet|meters{{/well-unit}})
Reverberation Time, t (seconds)5,9,10
Areas for learning
Areas for lectures
Areas for conferencing
v < {{well-unit}}10,000 ft3|280 m3{{/well-unit}}
t ≤ 0.6
{{well-unit}}10,000 ft3|280 m3{{/well-unit}} ≤ v ≤ {{well-unit}}20,000 ft3|570 m3{{/well-unit}}
t ≤ 0.8
v > {{well-unit}}20,000 ft3|570 m3{{/well-unit}}
t ≤ 1.0
Areas with regularly used PA systems
N/A
t ≤ 1.5
Areas for dining
N/A
t ≤ 1.0
Areas for fitness
v < {{well-unit}}10,000 ft3|280m3{{/well-unit}}
t ≤ 0.8
{{well-unit}}10,000 ft3|280 m3{{/well-unit}} ≤ v ≤ {{well-unit}}20,000 ft3|570 m3{{/well-unit}}
t ≤ 1.1
v > {{well-unit}}20,000 ft3|570 m3{{/well-unit}}
t ≤ 1.8
Areas for music rehearsal
v < {{well-unit}}10,000 ft3|280 m3{{/well-unit}}
t ≤ 1.1
{{well-unit}}10,000 ft3|280 m3{{/well-unit}} ≤ v ≤ {{well-unit}}20,000 ft3|570 m3{{/well-unit}}
t ≤ 1.4
Where room types include multiple use types (e.g., learning and fitness) use the limits that include the lower reverberation time or range.
Verification: Technical Document (Audited)
Modeling Report
Option 2: Reverberation time, performance
For projects in which the room types listed in the table cumulatively make up at least 10% of occupiable project area, the following requirements are met:
Reverberation time is within the ranges shown in the following table:
Room Type
Room Volume, v (cubic {{well-unit}}feet|meters{{/well-unit}})
Reverberation Time, t (seconds)5,9,10
Areas for learning
Areas for lectures
Areas for conferencing
v < {{well-unit}}10,000 ft3|280 m3{{/well-unit}}
t ≤ 0.6
{{well-unit}}10,000 ft3|280 m3{{/well-unit}} ≤ v ≤ {{well-unit}}20,000 ft3|570 m3{{/well-unit}}
t ≤ 0.8
v > {{well-unit}}20,000 ft3|570 m3{{/well-unit}}
t ≤ 1.0
Areas with regularly used PA systems
N/A
t ≤ 1.5
Areas for dining
N/A
t ≤ 1.0
Areas for fitness
v < {{well-unit}}10,000 ft3|280 m3{{/well-unit}}
t ≤ 0.8
{{well-unit}}10,000 ft3|280 m3{{/well-unit}} ≤ v ≤ {{well-unit}}20,000 ft3|570 m3{{/well-unit}}
t ≤ 1.1
v > {{well-unit}}20,000 ft3|570 m3{{/well-unit}}
t ≤ 1.8
Areas for music rehearsal
v < {{well-unit}}10,000 ft3|280 m3{{/well-unit}}
t ≤ 1.1
{{well-unit}}10,000 ft3|280 m3{{/well-unit}} ≤ v ≤ {{well-unit}}20,000 ft3|570 m3{{/well-unit}}
t ≤ 1.4
Where room types include multiple use types (e.g., learning and fitness) use the limits that include the lower reverberation time or range.
Refer to the Performance Verification Guidebook for information on sensor/testing requirements, required testing duration and compliance calculations.
Verification: Performance Test, Technical Document (Individual)
Technical Document: A list of room volumes for all applicable spaces.
Performance verification: Reverberation Time
Test method:
- For the noise source impulse:
- If generated via balloon burst, inflate balloon to 0.4 m [16 in] diameter. Then, arm or ready the sound level meter by measuring the baseline background noise level. Once the meter is armed for impulse, burst balloon using a pen or similar. Allow approximately 10 seconds for the meter to capture impulse response at all frequencies.
- If generated via loudspeaker, arm and ready the meter by measuring the baseline background noise level. Then, excite the room by turning the loudspeaker on to approximately 90 dBA using a white/pink noise generator. Once the sound level meter is armed for impulse measurement, turn off the sound source and wait approximately 10 seconds for the sound level meter to capture the impulse response at all frequencies.
Device requirements:
Balloon of minimum diameter 0.4 m [16 in]
OR
Loudspeaker:
- Minimum 0.25 m [10 in] diameter
- Minimum frequency response of at least 100 Hz – 4 kHz
- Maximum output of at least 100 dB
- Noise generator capable of producing pink noise signal of equal sound energy across all frequencies of interest
Reporting and compliance:
- The average RT60 value from 500 Hz - 1 kHz of the three measurements per measurement location is used to determine compliance with the WELL threshold.
WELL Core:
Meet these requirements in non-leased spaces. To earn an additional point, also meet these requirements in leased spaces.
WELL Core projects where non-leased space represents 40% or more of total project area may pursue the additional point without achieving the feature requirements in tenant spaces. Projects utilizing this pathway should include a note on the documentation required by the feature.
Frequently asked questions
Are open plan offices included in any of the room types listed in this feature?
No, open plan offices are not covered by the requirements of this feature. Reverberation time values can fluctuate greatly across the floor plate of open offices, making reverberation time difficult to quantify and design. Furthermore, there is not yet strong evidence that links higher reverberation times in open offices to adverse conditions for occupants. More suitable metrics include articulation index (AI), spatial decay of sound (D2s), radius of distraction (rD), and background sound (dBA).
References
- Klatte M, Bergström K, Lachmann T. Does noise affect learning? A short review on noise effects on cognitive performance in children. Front Psychol. 2013;4(August):1-6. doi:10.3389/fpsyg.2013.00578
- Klatte M, Hellbrück J, Seidel J, Leistner P. Effects of Classroom Acoustics on Performance and Well-Being in Elementary School Children: A Field Study. Environ Behav. 2010;42(5):659-692. doi:10.1177/0013916509336813
- Venetjoki N, Kaarlela-Tuomaala A, Keskinen E, Hongisto V. The effect of speech and speech intelligibility on task performance. Ergonomics. 2006;49(11):1068-1091. doi:10.1080/00140130600679142
- Belojević G, Öhrström E, Rylander R. Effects of noise on mental performance with regard to subjective noise sensitivity. Int Arch Occup Environ Health. 1992;64(4):293-301. doi:10.1007/BF00378288
- Ihrig W, The National Academies of Sciences Engineering Medicine, Transportation Research Board. Improving Intelligibility of Airport Terminal Public Address Systems. 2017. doi:10.17226/24839
- Heylighen A, Rychtarikova M, Vermeir G. Designing Spaces for Every Listener. Univers Access Inf Soc. 2010;9(3):283-292.
- The National Disability Authority’s Centre for Excellence in Universal Design. Building for Everyone: A universal design approach. 2012:4-106.
- Centre for Excellence in Universal Design. Internal environment and services. In: Building for Everyone: A Universal Design Approach. Centre for Excellence in Universal Design. http://universaldesign.ie/Built-Environment/Building-for-Everyone/.
- Architectural Joint Technical Committee AV-004 Acoustical. AS/NZS 2107:2016. 2016:24.
- General Services Administration. Sound Matters: How to Achieve Acoustic Comfort in the Contemporary Office. 2011. https://www.wbdg.org/FFC/GSA/gsa_soundmatters.pdf.
- General Services Administration, Service PB. PBS-P100 Facilities Standards for the Public Buildings Service. 2016;(March):333. doi:10.1017/CBO9781107415324.004
- ANSI/INFOCOMM. ANSI/INFOCOMM 10:2013 Audiovisual Systems Performance Verification. 2013.
- InfoComm International. AV / IT Infrastructure Guidelines for Higher Education.
- Publication BSIS. BSI Standards Publication - Sound system equipment - Part 4. 2011.