A14 Microbe and Mold Control (WELL v2, Q2 2025)
Concept: Air · Type: Optimization · Maximum points: 1
Intent
Reduce mold and bacteria growth within the building mechanical system.Summary
This WELL feature requires projects to utilize UVGI systems and/or conduct regular inspections on components of the cooling system to reduce or eliminate growth of microbes and mold.Issue
Mold will grow in places with an acceptable temperature range, a nutrient source and sufficient moisture.1 Air conditioner systems, specifically cooling coils, have high levels of moisture condensation and serve as the perfect breeding grounds for mold.2 Mold developed on cooling coils may shed particles into the building’s indoor air and trigger asthma, headaches, allergies and other respiratory system disorders.3–6 Exposure to mold has also been associated with hypersensitivity pneumonitis, allergic rhinitis, bronchitis, lung tumor development, eczema and toxic mold syndrome.5,7
Evidence
The growth of microorganisms and mold can be prevented and mitigated through a combination of regular mold inspections and placement of microbe inactivation techniques, such as Ultraviolet Germicidal Irradiation (UVGI) systems. Periodic inspections and maintenance of cooling systems are good preventative methods to reduce system failures that contribute to an increased potential for mold proliferation. Expenses associated with proper maintenance will often offset typical costs associated with mold remediation.1 UVGI has been shown to dramatically reduce mold and bacteria growth on cooling coils and destroy microbial films that accumulate on their surfaces.8 Studies have also associated the implementation of UVGI systems with a simultaneous reduction in viable microorganisms and respiratory disorders in the workplace.9
Requirements
A14.1 Implement Ultraviolet Treatment for HVAC Surfaces — 1 point
Applies to: All Spaces.
Meet all of the following options:
Option 1: UV system design
The following requirements are met:
All central air handling units use ultraviolet lamps to irradiate the surfaces of the cooling coils and drain pans.10
All cooling coils and drain pans not associated with central air handling units (e.g., those used in fan coil units or supplementary air handling units) either:
- Are irradiated by ultraviolet lamps.
- May be opened for inspection for mold growth and cleaned, if necessary.
Verification: On-site Photographs, Letter of Assurance – Engineer
Photographs should showcase:
1) For air handling units: UV lamps, cooling coils and drain pan taken when the UV lamp is NOT in operation.
2) For fan coil units: UV lamps (if present), cooling coils and drain pan showing no evidence of visible mold growth.
Quantity:
1) Photographs of at least 10% of air handling units and 10% of fan coil units, up to a combined maximum of five units.
Option 2: UV system maintenance and inspection
The following requirements are met:
Evidence that the ultraviolet lamps have been replaced or maintained, according to manufacturer's recommendation is submitted annually through the WELL digital platform.
- All cooling coils without ultraviolet lamps (if applicable) are inspected on a quarterly basis for mold growth and cleaned if necessary. Dated photos demonstrating adherence are submitted annually through the WELL digital platform.
Verification: On-going Maintenance Report
WELL Core:
Meet these requirements in the whole building. Up to 10% of the total area occupied by tenants can be excluded from the feature scope.References
- Air Conditioning Heating & Refrigeration News. Reducing Mold Growth in HVAC Equipment. https://www.enviro-tec.com/pdf/catalog/WP-ReducingMoldGrowth.pdf. Published 2003.
- Fink R. Mold/Bacteria Protection of A/C Coil. ACHR News. https://www.achrnews.com/articles/106240-mold-bacteria-protection-of-a-c-coil. Published 2008.
- Zock J-P, Jarvis D, Luczynska C, Sunyer J, Burney P, European Community Respiratory Health Survey. Housing characteristics, reported mold exposure, and asthma in the European Community Respiratory Health Survey. J Allergy Clin Immunol. 2002;110(2):285-292. https://www.jacionline.org/article/S0091-6749(02)00092-1/pdf.
- Mendell MJ, Mirer AG, Cheung K, Tong M, Douwes J. Respiratory and allergic health effects of dampness, mold, and dampness-related agents: A review of the epidemiologic evidence. Environ Health Perspect. 2011;119(6):748-756. doi:10.1289/ehp.1002410
- Fisk WJ, Eliseeva EA, Mendell MJ. Association of residential dampness and mold with respiratory tract infections and bronchitis: A meta-analysis. Environ Heal A Glob Access Sci Source. 2010;9(1):72. doi:10.1186/1476-069X-9-72
- Jones R, Recer GM, Hwang SA, Lin S. Association between indoor mold and asthma among children in Buffalo, New York. Indoor Air. 2011;21(2):156-164. doi:10.1111/j.1600-0668.2010.00692.x
- Pettigrew HD, Selmi CF, Teuber SS, Gershwin ME. Mold and human health: Separating the wheat from the chaff. Clin Rev Allergy Immunol. 2010;38(2-3):148-155. doi:10.1007/s12016-009-8175-5
- Berkeyley Lab, LBNL Indoor Environment Group. Using Ultraviolet Germicidal Lights for Air Cleaning. https://iaqscience.lbl.gov/air-uv.
- Dick Menzies, Julia Popa, James A Hanley, Thomas Rand DKM. Effect of Ultraviolet Germicidal Lights Installed in Office Ventilation Systems on Workers’ Health and Wellbeing: Double-Blind Multiple Crossover Trial.
- The American Society of Heating Refrigerating and Air-Conditioning Engineers. Standard 185.2-2014 -- Method of Testing Ultraviolet Lamps for Use in HVAC&R Units or Air Ducts to Inactivate Microorganisms on Irradiated Surfaces.; 2014. https://www.techstreet.com/standards/ashrae-185-2-2014?product_id=1881838.