W04 Enhanced Water Quality (WELL v2, Q2 2025)
Concept: Water · Type: Optimization · Maximum points: 1
Intent
Provide access to drinking water without unpleasant taste, odor and appearance.
Summary
This WELL feature requires projects to provide drinking water that meets thresholds on chemicals that affect aesthetics and taste concerns.Issue
Even when health-based thresholds for water quality are met, water may be found unappealing to drink because of taste, odor and appearance concerns. For example, high levels of chloride contribute to a salty taste and iron can give the water a reddish appearance.1 Therefore, some regulatory bodies set non-enforceable limits based on human detectability and acceptability for these substances.2,3Evidence
Like pollutants with health-based concerns, the treatment system to address nuisance chemicals depends on the contaminant of interest. Treatment options include filtration with carbon media and reverse osmosis.Impact
By managing nuisance chemicals, projects can provide more appealing and palatable drinking water.Requirements
W04.1 Meet Thresholds for Drinking Water Taste — 1 point
Applies to: All Spaces.
Water delivered to the project for human consumption meets the following thresholds:
Aluminum ≤ 0.2 mg/L.2
Chloride ≤ 250 mg/L.2
Copper ≤ 1 mg/L.2
Manganese ≤ 0.05 mg/L.
Iron ≤ 0.3 mg/L.2
Silver≤ 0.1 mg/L.2
Sodium ≤ 270 mg/L.3
Sulfate ≤ 250 mg/L.2
Zinc ≤5 mg/L.2
Total Dissolved Solids (TDS) ≤ 500 mg/L.2
Free Chlorine ≤ 1.25 mg/L.4
Refer to the Performance Verification Guidebook for information on sensor/testing requirements, required testing duration and compliance calculations.
Verification: Performance Test
Performance verification: Disinfectants
Test method:
- Take measurements of total and free chlorine of samples by adding the appropriate reagents as specified by the chlorine meter manufacturer. To calculate residual chloramines, subtract the free chlorine value from the total chlorine value.
- Repeat the process twice, for a total of three samples per water fixture tested.
Device requirements:
- Measurement range: 0-5 mg/L
- Reporting resolution: 0.01 mg/L or finer
- Accuracy: ±0.02 mg/L at 1.00 mg/L
Reporting and compliance:
- At each fixture, the average of the three samples must comply with the requirements in WELL.
Performance verification: Laboratory-based parameters (except lead)
Test method:
- Appropriate sampling vials must be obtained from the laboratory prior to performance testing.
- Follow all laboratory procedures for collecting and packaging the sample.
- Package and ship sample to third party testing laboratory per the laboratory’s instructions.
- This parameter is tested at drinking water fixtures and water fixtures used for cooking purposes for commercial kitchens (as applicable).
Reporting and compliance:
- The sample from every fixture tested must meet the requirements in WELL for each of the contaminants being tested.
- For Styrene samples, a "Not Detected" measurement with a limit of detection of .001 mg/L is considered acceptable.
WELL Core:
Meet these requirements in the whole building. Water will be sampled from non-leased spaces and the project must either:
- Confirm that the same water treatment system (if applicable) will be used in all leased spaces.
- Provide an allowance to tenants to purchase the same type of treatment system (if applicable) in leased spaces. If there is no water supply in non-leased spaces, water will be sampled from leased spaces.
Frequently asked questions
For the Water concept, are the WELL requirements for drinking water testing applicable only to cold water?
According to the WELL Performance Verification Guidebook, sampling for water for human contact is conducted on cold water. Hot water sources such as coffee makers are out of scope. However, for mixed water faucets, the hot supply should be turned off. If water temperature conditions cannot be altered, testing is conducted using the available water.
References
- World Health Organization. Guidelines for drinking-water quality. 4th ed. Geneva, Switzerland: WHO Press; 2017.
- U.S. Environmental Protection Agency. National Secondary Drinking Water Regulations. https://www.epa.gov/dwstandardsregulations/secondary-drinking-water-standards-guidance-nuisance-chemicals. Published 2017. Accessed.
- Health Canada. Guidelines for Canadian Drinking Water Quality—Summary Table. https://www.canada.ca/en/health-canada/services/environmental-workplace-health/reports-publications/water-quality/guidelines-canadian-drinking-water-quality-summary-table.html. Published 2017. Accessed.
- Crider Y, Sultana S, Unicomb L, Davis J, Luby SP, Pickering AJ. Can you taste it? Taste detection and acceptability thresholds for chlorine residual in drinking water in Dhaka, Bangladesh. Science of The Total Environment. 2018;613-614:840-846.