A01 Air Quality (WELL v2, Q2 2025)
Concept: Air · Type: Precondition
Intent
Provide a basic level of indoor air quality that contributes to the health and well-being of building users.
Summary
This WELL feature requires projects to provide acceptable air quality levels, as determined by public health authorities.
Issue
Exposure to air pollutants, such as Volatile Organic Compounds (VOCs), ozone, particulate matter, carbon monoxide and others has been shown to increase the risk of respiratory and cardiovascular diseases, in addition to causing thousands of cancer deaths annually.1 Inhaling pollutants presents symptoms including headaches, dry throat, eye irritation and runny nose that may later develop into extreme health outcomes, such as asthma attacks and cancer.2–4 In addition, radon exposure is the second leading cause of lung cancer, after tobacco use.5 Therefore, it is important to define indoor air quality levels that minimize risk to human health.
Evidence
The World Health Organization (WHO) and other regulatory bodies, such as the U.S. Environmental Protection Agency (EPA) identify a list of “criteria” air pollutants. They have established permissible levels for such criteria pollutants based on epidemiological studies that show the relationships between concentrations of these pollutants, duration of exposure and health risks. Achieving the goal of clean indoor air as defined by permissible levels, requires the joint efforts of both professionals and building users in the implementation of adequate approaches. Indoor air quality can be properly managed through different features listed in the WELL Air concept, including source control strategies, passive and active building design and operation strategies and human behavior interventions. Effective mechanical ventilation is particularly effective at bringing radon below acceptable thresholds.6,7
Requirements
A01.1 Meet Thresholds for Particulate Matter — Precondition
Applies to: All Spaces; excluding Commercial Kitchen Spaces, Industrial.
Meet any one of the following options:
Option 1: Acceptable thresholds
The following thresholds are met in occupiable spaces:
PM2.5: 15 µg/m3 or lower.8
PM10: 50 µg/m3 or lower.9
Verification: Performance Test OR Sensor Data
Performance verification: PM2.5 and PM10
Test method:
- Measurement method: real-time direct reading instrument.
- Duration of measurement: minimum of one continuous hour (10 minutes of acclimation time followed by 50 minutes of measurement time), with measurements recorded at least once every minute.
Device requirements:
- Instrument type: light-scattering airborne particle counter
- Measurement range: 1-1,000 μg/m3
- Instrument accuracy (at the size specified by the manufacturer): ≤ 15%
- On-screen resolution: 1 μg/m3
- Lower detectable limit: 1 μg/m3
- Reporting interval: one minute maximum
- Calibration: instrument must be calibrated within the manufacturer’s specification (maximum interval: one year), and the calibration record (i.e., the measurement result obtained during calibration) must be traceable to a National Metrological Institute, such as NIST, NPL or PTB.to a National Metrological Institute, such as NIST, NPL or PTB.
Reporting and compliance:
- Compliance is based on the median value collected during the measurement time at each sampling point compared against the requirement in WELL + a tolerance of 20%.
Option 2: Modified thresholds in polluted regions (eligible up to Gold level)
For buildings where the annual average outdoor PM2.5 level is 35 µg/m3 or higher, the following thresholds are met:
PM2.5: 25 µg/m3 or lower.10
PM10: 50 µg/m3 or lower.10
Verification: Performance Test OR Sensor Data, Technical Document (Shareable)
Technical Document: A report reflecting annual average PM2.5 levels
Option 3: Dynamic thresholds in polluted regions (eligible up to Silver level)
For buildings where the annual average outdoor PM2.5 level is 35 µg/m3 or higher, the following thresholds are met:
PM2.5 less than or equal to 30% of the 24- or 48-hour average of outdoor levels on the day(s) of performance testing.
PM10 less than or equal to 30% of the 24- or 48-hour average of outdoor levels on the day(s) of performance testing.
Verification: Performance Test OR Sensor Data, Technical Document (Shareable)
Technical Document: A report reflecting annual average PM2.5 levels
Applies to: Commercial Kitchen Spaces, Industrial.
Meet any one of the following options:
Option 1: Acceptable thresholds
The following threshold is met:
PM2.5: 35 µg/m³ or lower.8
Verification: Performance Test OR Sensor Data
Option 2: Dynamic thresholds in polluted regions (eligible up to Silver level)
For buildings where the annual average outdoor PM2.5 level is 35 µg/m3 or higher, the following thresholds are met:
PM2.5 equal to 30% of the 24- or 48-hour average of outdoor levels on the day(s) of performance testing.
PM10 equal to 30% of the 24- or 48-hour average of outdoor levels on the day(s) of performance testing.
Verification: Performance Test OR Sensor Data, Technical Document (Shareable)
Technical Document: A report reflecting annual average PM2.5 levels
Multifamily residential projects may achieve WELL Certification at the Bronze or Silver level without testing in dwelling units, but cannot achieve Gold or Platinum without testing in dwelling units. See Sampling Rates for Multifamily Residential in the WELL Performance Verification Guidebook for further details.
The World Health Organization’s Global Urban Ambient Air Pollution Database may be consulted to view outdoor air quality levels, available at https://www.who.int/data/gho/data/themes/air-pollution/who-air-quality-database.
Refer to the Performance Verification Guidebook for information on sensor/testing requirements, required testing duration and compliance calculations. Refer to the Performance Verification Guidebook for information on sensor/testing requirements, required testing duration and compliance calculations.
WELL Core:
Meet these requirements in non-leased spaces, provided these areas comprise at least 2.5% of the total project area. Otherwise, meet these requirements in non-leased space plus sufficient leased space to sum to 2.5% of the total project area.
A01.2 Meet Thresholds for Organic Gases — Precondition
Applies to: All Spaces.
Meet any one of the following options:
Option 1: Laboratory-based VOC tests
The following thresholds are met in occupiable spaces:
Benzene (CAS 71-43-2): 10 µg/m³ or lower.11
Formaldehyde (CAS 50-00-0): 50 µg/m³ or lower.12
Toluene (CAS 108-88-3): 300 µg/m³ or lower.13
Verification: Performance Test
Performance verification: Formaldehyde and Acetaldehyde
Test method:
- Samples are taken through an active collection in accordance with ISO 16000-3, ASTM D5197, NIOSH 2016, EPA TO-11 (or 11A) or EPA Compendium Method IP-6 (or 6A).
- Minimum of one continuous hour OR the duration of sampling volume prescribed by the referenced testing methodology.
- A minimum of one exposure field blank sample must be prepared and analyzed per day of sampling.
Device requirements:
- Laboratory materials and/or samplers must be prepared according to the referenced testing methodology and meet the referenced testing methodology requirements.
- Air sampling pumps utilized in active collection measurements must be capable of meeting the airflow rates prescribed by the referenced testing methodology (if applicable).
Reporting and compliance:
- Compliance is based on the measured concentration at each location compared against the requirement in WELL + tolerance of 20%.
Performance verification: VOCs (except Formaldehyde and Acetaldehyde)
Test method:
- Samples are taken through an active collection in accordance with ISO 16000-6, ASTM D5197, EPA TO-15 or EPA TO-17.
- The following methods are acceptable alternatives for speciating individual VOCs:
- Acrylonitrile: NIOSH 1604 (modified methodology acceptable to reach ppb concentrations)
- Caprolactam: OSHA PV2012 (modified methodology acceptable to reach ppb concentrations)
- A minimum of one exposure field blank sample per day of sampling must be prepared and analyzed.
Device requirements:
- Laboratory materials and/or samplers must be prepared according to the referenced testing methodology and meet the referenced testing methodology requirements.
- Air sampling pumps utilized in active collection measurements must be capable of meeting the airflow rates prescribed by the referenced testing methodology (if applicable).
Reporting and compliance:
- For tests for Features A01 or A05, compliance is based on the measured concentration at each location compared against each VOC’s requirement in WELL + tolerance of 5%.
- For tests of WELL v1 Feature 01, compliance is based on each location either meeting the conditions above or the measured TVOC concentration compared against the requirement in WELL.
Option 2: TVOC continuous monitoring
The following threshold is met in occupiable spaces:
Total VOC: 500 µg/m3 or lower.
Projects undergoing recertification which were previously awarded Feature A08 must consider all data collected since the previous (re)certification.
Verification: Sensor Data
Multifamily residential projects may achieve WELL Certification at the Bronze or Silver level without testing in dwelling units, but cannot achieve Gold or Platinum without testing in dwelling units. See Sampling Rates for Multifamily Residential in the WELL Performance Verification Guidebook for further details.
Refer to the Performance Verification Guidebook for information on sensor/testing requirements, required testing duration and compliance calculations.
WELL Core:
Meet these requirements in non-leased spaces, provided these areas comprise at least 2.5% of the total project area. Otherwise, meet these requirements in non-leased space plus sufficient leased space to sum to 2.5% of the total project area.
A01.3 Meet Thresholds for Inorganic Gases — Precondition
Applies to: All Spaces; excluding Commercial Kitchen Spaces, Industrial.
The following thresholds are met in occupiable spaces:
Carbon monoxide: 10 mg/m³ [9 ppm] or lower.8
Ozone: 100 µg/m³ [51 ppb] or lower.10
Verification: Performance Test OR Sensor Data
Performance verification: Carbon Monoxide
Test method:
- Minimum of one continuous hour (10 minutes of acclimation time followed by 50 minutes of measurement time), with measurements recorded at least once every minute.
Device requirements:
- Real-time direct reading instrument.
- Measurement range: 0-25 ppm
- Instrument resolution: 0.1 ppm
- Lower detectable limit: 0.1 ppm
- Calibration: instrument must be within the calibration period
Reporting and compliance:
- Compliance is based on the median value collected during the measurement time at each sampling compared with the WELL requirements.
Performance verification: Ozone
Test method:
- Minimum of one continuous hour (10 minutes of acclimation time followed by 50 minutes of measurement time), with measurements recorded at least once every minute.
Device requirements:
- Real-time direct reading instrument.
- Measurement range: 0-500 ppb
- On-screen resolution: 1 ppb
- Lower detectable limit: 3 ppb
- Calibration: instrument must be within the calibration period
Reporting and compliance:
- Compliance is based on the median value collected during the measurement time at each sampling point compared against the requirement in WELL + a tolerance of 5%.
Applies to: Commercial Kitchen Spaces, Industrial.
The following thresholds are met:
Carbon monoxide: 34 mg/m³ [30 ppm] or lower.14
Ozone: 100 µg/m³ [51 ppb] or lower.10
Verification: Performance Test OR Sensor Data
Multifamily residential projects may achieve WELL Certification at the Bronze or Silver level without testing in dwelling units, but cannot achieve Gold or Platinum without testing in dwelling units. See Sampling Rates for Multifamily Residential in the WELL Performance Verification Guidebook for further details.
Refer to the Performance Verification Guidebook for information on sensor/testing requirements, required testing duration and compliance calculations.
WELL Core:
Meet these requirements in non-leased spaces, provided these areas comprise at least 2.5% of the total project area. Otherwise, meet these requirements in non-leased space plus sufficient leased space to sum to 2.5% of the total project area.
A01.4 Meet Thresholds for Radon — Precondition
Applies to: All Spaces.
Meet any one of the following options:
Option 1: Radon testing
The following threshold is met on the lowest regularly occupiable floor:
Radon: 0.15 Bq/L [4 pCi/L] or lower, as tested by a professional demonstrated not to have a conflict of interest with the WELL project. One test is conducted per {{well-unit}}25,000 ft2|2300 m2{{/well-unit}} of regularly occupied space.
Verification: Sensor Data, Technical Document (Individual)
Technical Document: Radon test report
Option 2: Mechanical ventilation
For regularly occupied spaces at or below grade, the following requirement is met:- All regularly occupied spaces at or below grade meet Feature A03, Part 1, Option 1.
Verification: Letter of Assurance – Engineer
Option 3: Above-grade
One of the following requirements are met in regularly occupied spaces:
Is completely located on or above the third floor of the building.
Is constructed with raised-pier foundations (e.g., without a solid perimeter wall) and all mechanical equipment is elevated off the ground.
Verification: Letter of Assurance – Owner
Refer to the Performance Verification Guidebook for information on sensor/testing requirements, required testing duration and compliance calculations.
WELL Core:
For Option 1, meet these requirements in non-leased spaces at or below grade, provided these areas comprise at least 2.5% of the total project area at or below grade. Otherwise, meet these requirements in non-leased space plus sufficient leased space to sum to 2.5% of the total project area at or below grade.
For Option 2, meet the requirements in non-leased spaces at or below grade. In leased spaces at or below grade, provide sufficient outdoor air; installation of ducts and diffusers is not required.
For Option 3, meet these requirements in the whole building.
A01.5 Measure Air Parameters — Precondition
Applies to: All Spaces; excluding Dwelling Units.
The following pollutants are monitored in occupiable spaces at intervals no longer than once per year, and the results are submitted annually through the WELL digital platform. To determine the required sample locations and quantity, refer to the WELL Performance Verification Guidebook.
PM2.5
PM10.
One of the following:
- Total VOC.
- Benzene, Formaldehyde, Toluene.
Carbon Monoxide.
Ozone.
Projects are not required to follow the device requirements or test methods described in the Performance Verification Guidebook.
Verification: On-going Data Report
WELL Core:
Meet these requirements in non-leased spaces. Calculate the number of samples using the area of non-leased space.
Frequently asked questions
Where can ambient air quality be found so that a project can determine if it is eligible to use the PM limits in options 2 and 3 for Feature A01 Part 1?
One resource projects may use is the World Health Organization’s Global Urban Ambient Air Pollution Database, available at https://www.who.int/data/gho/data/themes/air-pollution/who-air-quality-database.
If a monitoring device with sensors installed to meet A08.1 measures the pollutants listed in A01.1, A01.2, and A01.3, can the monitoring device with sensors installed for A08.1 be used to comply with Feature A01.5?
Yes, monitoring devices with sensors installed for A08.1 can also be used to comply with A01.5 so long as all of the relevant air quality parameters are monitored (TVOCs may be monitored in lieu of formaldehyde, toluene, and benzene). If an individual monitor with sensors cannot monitor all relevant air quality parameters, additional devices or on-site testing will need to be utilized. Note: the number of monitors installed for Feature A08 will likely be higher than the minimum number of test locations in the Performance Verification Guidebook.
For projects that utilize continuous monitors, what data is required to be submitted for on-going data reporting for Part 5?
Projects must provide at least one annual measurement from each monitor for each pollutant listed for a sufficient number of test locations. Monitoring reports which include multiple measurements over regular intervals are acceptable. To determine the required sample locations and quantity, refer to the WELL Performance Verification Guidebook.
I am using sensors installed in my project to meet Feature A01.5; where should I look in the WELL Performance Verification Guidebook to know how many I need to install?
If you are only looking to earn Feature A01.5 and not A08.1 or an Air Concept feature part that will be verified by Sensor Data (i.e., A01.1, A01.2, A01.3, A01.4, A03.1, A05.1, A05.3, A06.1), then you can look in the Quantity of Sample Locations table in the Air section of Performance Testing Requirements. In this case, there are also no requirements for device quality.
If you are looking to also earn Feature A08.1 and / or any Air Concept feature parts verified by Sensor Data, then look in the Monitor Density table in the Continuous Monitoring Requirements section and be sure the monitors meet the device quality requirements in Sensor Technical Specification Requirements for sufficient parameters.
Does my WELL Core project need to sample in both non-leased and leased spaces for all Feature A01 parts if the project is not pursuing the matching Feature A05 parts?
All projects have the option to only pursue select parts under Feature A05, despite being required to pursue all parts under Feature A01. When determining sample quantities, WELL Core projects may pursue testing in only non-leased spaces for the Feature A01 parts for which they are not pursuing the matching Feature A05 part. Refer to the WELL Performance Verification guidebook for more on sample quantities for WELL Core projects pursuing both Feature A01 and Feature A05, Part 1, 2, or 3.
References
- Franklin BA, Brook R, Arden Pope C. Air pollution and cardiovascular disease. Curr Probl Cardiol. 2015;40(5):207-238. doi:10.1016/j.cpcardiol.2015.01.003
- Joshi S. The sick building syndrome. Indian J Occup Environ Med. 2008;12(2):61. doi:10.4103/0019-5278.43262
- Selgrade MK, Plopper CG, Gilmour MI, Conolly RB, Foos BSP. Assessing the health effects and risks associated with children’s inhalation exposures - Asthma and allergy. J Toxicol Environ Heal - Part A Curr Issues. 2008;71(3):196-207. doi:10.1080/15287390701597897
- U.S. Environmental Protection Agency. Indoor Air Pollution: An Introduction for Health Professionals. https://www.epa.gov/indoor-air-quality-iaq/indoor-air-pollution-introduction-health-professionals.
- World Health Organization. WHO Handbook on Indoor Radon: A Public Health Perspective. Presented at the: 2009. https://www.who.int/ionizing_radiation/env/9789241547673/en/.
- Yang S, Goyette Pernot J, Hager Jörin C, Niculita-Hirzel H, Perret V, Licina D. Radon Investigation in 650 Energy Efficient Dwellings in Western Switzerland: Impact of Energy Renovation and Building Characteristics. Atmosphere (Basel). 2019;10(12):777. doi:10.3390/atmos10120777
- Hadlich DE, Grimsrud DT. Radon in Institutional Buildings : The Impacts of Conservation Strategies. Radon Institutional Build Impacts. 1991;(1990).
- U.S. Environmental Protection Agency. NAAQS Table. https://www.epa.gov/criteria-air-pollutants/naaqs-table.
- European Commission. Proposal for a directive of the European Parliament and of the Council on ambient air quality and cleaner air for Europe - COM(2005) 447 Final. Off J Eur Union. 2005;0183:1-67.
- World Health Organization. Air Quality Guidelines for Particulate Matter, Ozone, Nitrogen Dioxide and Sulfur Dioxide. Geneva, Switzerland; 2005. http://apps.who.int/iris/bitstream/handle/10665/69477/WHO_SDE_PHE_OEH_06.02_eng.pdf;jsessionid=CD44465FAC0A1628540C4A2BDF0B51CD?sequence=1.
- French Agency for Food Environmental and Occupational Health and Safety. ANSES’s List of Indoor Air Quality Guideline Values.; 2018. https://www.anses.fr/fr/system/files/Tableau_VGAI_Juillet2018EN.pdf.
- Health Canada. Residential Indoor Air Quality Guideline: Formaldehyde.; 2006. https://www.canada.ca/content/dam/canada/health-canada/migration/healthy-canadians/publications/healthy-living-vie-saine/formaldehyde/alt/formaldehyde-eng.pdf.
- California Office of Environmental Health Hazard Assessment. Acute, 8-hour and Chronic Reference Exposure Level (REL) Summary. https://oehha.ca.gov/air/general-info/oehha-acute-8-hour-and-chronic-reference-exposure-level-rel-summary. Published 2019.
- Health and Safety Executive. EH40/2005 Workplace Exposure Limits.; 2011. http://www.hse.gov.uk/pUbns/priced/eh40.pdf.